| View previous topic :: View next topic |
| Author |
Message |
grinolot
Joined: 13 Jul 2004
Posts: 7
Location: Ohio
|
 Posted: Tue Jul 13, 2004 4:42 pm Post subject: |
 |
|
| Where it is and how do I operate it? |
|
| Back to top |
|
 |
Jack5541
Joined: 31 Jul 2003
Posts: 76
|
| Posted: Tue Jul 13, 2004 5:12 pm Post subject: |
|
|
| Well, Grinolot, there are several ways to trip the shutter on a Graphic. But first and foremost on a Crown, there should be cock/release levers on the front shutter. Please let us know what type of shutter you have and we can guide you along a little better. |
|
| Back to top |
|
|
grinolot
Joined: 13 Jul 2004
Posts: 7
Location: Ohio
|
|
| Back to top |
|
|
Dan Fromm
Joined: 14 May 2001
Posts: 2148
Location: New Jersey
|
| Posted: Tue Jul 13, 2004 5:46 pm Post subject: |
|
|
If you look closely at the picture, you'll see a tab sticking out from the front standard and in contact with the shutter's release lever. This tab connects by cable to a push button on the lower left side of the camera body. If you look at the camera body, you'll see two recesses on the upper edges, where the focusing knobs go when the door is closed. There's also something on the lower left side of the body that looks somewhat like a recess. This is the body release that connects by cable ...
Press the release and the tab will push down on the shutter's release lever; some minor fiddling may be needed to get it to work well with the shutter now on the camera. FWIW, the front release on my Speed works poorly, often not at all, with nearly all lenses not in the small Supermatic shutter that the original lens is in. I usually shoot from tripod, attach a standard cable release to the front shutter when I use the front shutter.
This will all be pretty obvious when you have the camera in your hands. Stop worrying and be patient. If you MUST worry, rest assured that you've made a horrible mistake and will die.
Cheers,
Dan |
|
| Back to top |
|
|
45PSS
Joined: 28 Sep 2001
Posts: 4081
Location: Mid Peninsula, Ca.
|
| Posted: Tue Jul 13, 2004 6:35 pm Post subject: |
|
|
Looking at the picture that you posted:
On the left side at the 9 o'clock position; shutter's release lever with the Crown's trip lever touching it.
11 o'clock position, green lever:
Flash sync/self timer X-strobe, M-flash bulbs, V-self time mode.
12 o'clock: flash sync connector. PC type.
1 o'clock: shutter cock lever. push clockwise (to the right) to cock shutter. Press body release as described in post above or press down on lever at 9 o'clock position. Shutter must be cocked prior to triping it.
2:30 o'clock: press to focus button for ground glass focusing. Cock shutter, press and hold down on button, trip shutter. With back of camera open look at the ground glass and you will see some form of light coming from the lens. To close shutter after focusing recock the shutter.
7 o'clock: aperture adjustment lever.
Chrome ring at outter front edge of shutter with knurled edge is the speed adjustment ring, turn it until speed is opposite arrow on black inner ring to set shutter speed. B-bulb, shutter stays open as long as shutter release is held down. T-time, shutter opens on first trip of shutter release after cocking and stays open until shutter release is triped again without recocking or shutter speed dial is moved to another setting.
Charles
_________________
While a picture may be worth a thousand words, a quality photograph is worth a million.
[ This Message was edited by: 45PSS on 2004-07-13 11:39 ] |
|
| Back to top |
|
|
grinolot
Joined: 13 Jul 2004
Posts: 7
Location: Ohio
|
| Posted: Tue Jul 13, 2004 7:31 pm Post subject: |
|
|
| Are shutter release cables available? If so, where would I find them? |
|
| Back to top |
|
|
t.r.sanford
Joined: 10 Nov 2003
Posts: 812
Location: East Coast (Long Island)
|
| Posted: Tue Jul 13, 2004 7:55 pm Post subject: |
|
|
The "Compur" shutter will accept any common or garden-variety cable release. These are available in a wide assortment of lengths from local camera stores and mail-order/online retailers (like Porter's).
May we assume that the internal cable, which connects the shutter tripping assembly on the camera front to the body release, is present and working properly? |
|
| Back to top |
|
|
grinolot
Joined: 13 Jul 2004
Posts: 7
Location: Ohio
|
| Posted: Tue Jul 13, 2004 8:03 pm Post subject: |
|
|
How would I test this?
It works OK when I cock the shutter and then trip it.
Todd |
|
| Back to top |
|
|
t.r.sanford
Joined: 10 Nov 2003
Posts: 812
Location: East Coast (Long Island)
|
| Posted: Tue Jul 13, 2004 8:35 pm Post subject: |
|
|
| As noted in a detailed earlier post, the body release (positioned to receive the tip of your right index finger) is connected to a vertical slide on the front standard by means of a long, slender cable that snakes under the bellows. If pressing the body release causes the slide on the front to move down, and the horizontal part of it trips the shutter on the way, then you are in business. |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
