Graflex.org Forum Index Graflex.org
Get help with your Graflex questions here
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

120 roll film holders

 
Post new topic   Reply to topic    Graflex.org Forum Index -> Film Help
View previous topic :: View next topic  
Author Message
mike sellers



Joined: 30 Aug 2001
Posts: 4
Location: Ohio

PostPosted: Thu Aug 30, 2001 6:02 pm    Post subject: Reply with quote

I have just acquired two Graflex roll film holders.On the RH 10 model with blue winding lever the dark slide hits the edge of the frame and won`t seat all the way unless you push in so it can clear.Is there any way to fix this?My other holder says RH 10-20 with a yellow lever; so does 10-20 mean it takes 220 film?
Back to top
View user's profile Send private message
Les



Joined: 09 May 2001
Posts: 2682
Location: Detroit, MI

PostPosted: Thu Aug 30, 2001 8:56 pm    Post subject: Reply with quote

Only half of your roll film holder will accept 220 film.

The RH10-20 back (the wrap around part) will accept either the 120 or the 220 insert.

_________________
"In order to invent, you need a good imagination and a lot of junk" Thomas Edison
Back to top
View user's profile Send private message
bertsaunders



Joined: 20 May 2001
Posts: 577
Location: Bakersfield California

PostPosted: Fri Aug 31, 2001 2:58 am    Post subject: Reply with quote

Mike a source for dark slide replacements
tpp@thompsonphoto.com
Bert
Back to top
View user's profile Send private message Send e-mail
mike sellers



Joined: 30 Aug 2001
Posts: 4
Location: Ohio

PostPosted: Fri Aug 31, 2001 7:54 pm    Post subject: Reply with quote

So,since the insert counter goes up to 20 then it is the 220 insert in 6x7 format?
Back to top
View user's profile Send private message
alecj



Joined: 09 May 2001
Posts: 853
Location: Alabama

PostPosted: Fri Aug 31, 2001 11:19 pm    Post subject: Reply with quote

The format is determined by the shell, not the insert. It contains the cutout for the film to be exposed. Since you are using an RH-20 insert in an RH-10 shell, yes, the format will be 6x7.
Back to top
View user's profile Send private message
mike sellers



Joined: 30 Aug 2001
Posts: 4
Location: Ohio

PostPosted: Sat Sep 08, 2001 3:33 pm    Post subject: Reply with quote

On my 2x3 RH-10 holder one of the roller pins that reside just above the dark slide is missing.Where can I buy another one? What is the purpose of these rollers and what would happen if I used the holder without replacing the roller? Thanks
Back to top
View user's profile Send private message
bertsaunders



Joined: 20 May 2001
Posts: 577
Location: Bakersfield California

PostPosted: Sat Sep 08, 2001 4:30 pm    Post subject: Reply with quote

Rollers are intended to keep film flat--dont waste film without either of them! Parts for
these roll holders are non existant, except
occasionally at auction, replacements are available! Bert

[ This Message was edited by: bertsaunders on 2001-09-08 09:33 ]
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Graflex.org Forum Index -> Film Help All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group