View previous topic :: View next topic |
Author |
Message |
scott bustrum
Joined: 23 Aug 2001 Posts: 4 Location: yorba linda, california
|
Posted: Fri Aug 24, 2001 2:50 am Post subject: |
|
|
i have a 120 roll film back called "22" graphic which fits my crown graphic pacemaker 23 just fine when i remove the spring clips and ground glass back. but how is the 22 holder now secured to the back of my camera? is there some other hardware that i need to hold the roll film back tight to the camera body, or is there some technique to use the spring clips? help!! scott b |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
bertsaunders
Joined: 20 May 2001 Posts: 577 Location: Bakersfield California
|
Posted: Sat Aug 25, 2001 6:26 pm Post subject: |
|
|
Graflex made a pair of springs for that
purpose--but they are near impossible to find! I think I have a pair of them in my parts box, but will have to find them to see what size parts camera they came from???
Your camera is a 2 x 3? Bert
[ This Message was edited by: bertsaunders on 2001-08-25 11:29 ] |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
scott bustrum
Joined: 23 Aug 2001 Posts: 4 Location: yorba linda, california
|
Posted: Sat Aug 25, 2001 7:45 pm Post subject: |
|
|
thank you for your reply, bert. my camera is a pacemaker crown graphic with the GRAFLEX back which is currently set up to accept the 2 1/4 x 3 1/4 sheet film magazines. this particular back is currently secured to the back of the camera body with spring clips.i have tried to re apply the clips in every possible combination, but it seems like i need a different style. my reference book "graphic graflex photography" 1941, indicaters that this graflex back will accect the roll film holder...but exactly how is not shown or discussed. any continued help would be appreciated. scott b |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
bertsaunders
Joined: 20 May 2001 Posts: 577 Location: Bakersfield California
|
Posted: Mon Aug 27, 2001 5:16 pm Post subject: |
|
|
Scott--Found the aux clips--after re'reading
your last post, am a little confused about the back you have on the camera!
The "FLEX" has a fixed bar on the bottom--
and a slider on the top! The "SPRING BACK",
has 2 LEAF springs, held in place by screws
"on center"--Have alternative to the aux
spring clips if you are interested--a better
way--via sketches and email!! Bert |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
scott bustrum
Joined: 23 Aug 2001 Posts: 4 Location: yorba linda, california
|
Posted: Wed Aug 29, 2001 2:55 am Post subject: |
|
|
thank you for your reply. yes, it is two leaf springs that retain the current back. I will take digital photos of the camera and the roll film holder and send them . I assume this site can accept an attachment to an e-mail? do you know? advise. thanx again scott b |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
bertsaunders
Joined: 20 May 2001 Posts: 577 Location: Bakersfield California
|
Posted: Wed Aug 29, 2001 5:00 pm Post subject: |
|
|
Havent seen anyway to "attach" to this post,
Unless you have a problem with direct contact, think reg email would work the best!
I havent found the way to post photos or sketches, without cluttering up the helpboard
with a bunch of extra time consumming, back and forth chit chat! Sometimes a solution to a problem takes many questions and answers! I
appreciate that direct to the point solutions, are really more productive, than
makeing this forum a Chat Room!
bert@etcrier.net |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
scott bustrum
Joined: 23 Aug 2001 Posts: 4 Location: yorba linda, california
|
Posted: Wed Aug 29, 2001 6:11 pm Post subject: |
|
|
Bert- good idea. I will send info to your e mail address . thanks for your interest in helping. scott b |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
bertsaunders
Joined: 20 May 2001 Posts: 577 Location: Bakersfield California
|
Posted: Fri Sep 07, 2001 8:49 pm Post subject: |
|
|
Scott and I have exchanged some photos, kicked around some ideas about what he has, and what his options are! We do know that he has a standard Spring Back, on his camera!
The Aux spring kit was one option--but it has the drawback of>>only usefull to attach
roll back or Grafmatic, usefull life
with heavy use is limited, and ground glass
focusing is not possible without modifications to the original back! Have found that the roll film back is difficult
to install under the aux springs, without
dissassembly, and some tugging and prying!
Best to leave the roll back in place, once positioned! The second option of coarse is
the Graflok back--drawbacks>>expensive and hard to find! Bert
|
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|