Graflex.org Forum Index Graflex.org
Get help with your Graflex questions here
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Yet another filter size question!

 
Post new topic   Reply to topic    Graflex.org Forum Index -> Lenses Help
View previous topic :: View next topic  
Author Message
Mike Wilson



Joined: 02 Aug 2002
Posts: 3

PostPosted: Fri Aug 02, 2002 7:05 pm    Post subject: Reply with quote

I've finally dug out my old 4x5 Speed Graphic again, and was wanting to find a lens hood to shoot with, and a UV filter to store it with. I've measured the lens as best I can, and it seems to be about 40mm., but the S.K. Grimes directions left me a bit mechanically-challenged. It's a Zeiss Jena Tessar f4.5 150 - can anyone confirm, deny, or otherwise correct my 40mm filter size guess before I order things by mail?
Back to top
View user's profile Send private message Send e-mail
Les



Joined: 09 May 2001
Posts: 2682
Location: Detroit, MI

PostPosted: Fri Aug 02, 2002 9:59 pm    Post subject: Reply with quote

Well I don't have that lens, but I do know tat 40.5mm was a common filter size. My 135 Xenar and some other lenses including some lenses from Leica i think.

Now why they picked 40.5mm is a different question
Back to top
View user's profile Send private message
RichS



Joined: 18 Oct 2001
Posts: 1468
Location: South of Rochester, NY

PostPosted: Sat Aug 03, 2002 3:35 am    Post subject: Reply with quote

I do have that lens on my View, but unfortunately do not have any screw-in filters for it so I can't offer anything but the mic'd dimensions. 40mm inside and 42mm outside. You might be able to find a 42mm push on series VI adapter, which is what I'd like t find... Whether or not the 40mm inside equates to a 40.5 or 41mm filter is beyond me. I have the 'how-to' someplace on the hard drive...somplace
If you find out for sure, post it here cause I'd like to know!
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Mike Wilson



Joined: 02 Aug 2002
Posts: 3

PostPosted: Mon Aug 05, 2002 4:10 pm    Post subject: Reply with quote

Thanks for the replies; I'll order a 40.5 and see if that fits and let you know....
Back to top
View user's profile Send private message Send e-mail
euvopana



Joined: 07 Aug 2002
Posts: 1
Location: Mexico

PostPosted: Thu Aug 08, 2002 4:25 am    Post subject: Reply with quote

Hello, I own a speedgraphic with a Kodak Ektar 127/4,7. Where can I get a slip on filter adapter and wich one. The outer diameter is 38mm or 1 1/2 inch.Anybody can help me? I like to use Polarizing filter and shade.
Volker Schlichting, German living in Mexico

Many thanks for your answers. But I still have a problem. What means slip on to series 6 filter? Will I have the posibility to screw on filters to this adapter and what size of screw on filters will I need or can I use? Specialy I will use a polarizing filter. As my Speedgraphic is not a reflex I have to put it on and off to my lens. Is this posible with this adapters?

[ This Message was edited by: euvopana on 2002-08-08 21:38 ]
Back to top
View user's profile Send private message
Les



Joined: 09 May 2001
Posts: 2682
Location: Detroit, MI

PostPosted: Thu Aug 08, 2002 2:38 pm    Post subject: Reply with quote

You need the 38mm /1.5" to Series VI slip on adapter made by the truck load in the 50s. The easiest for you might be ebay, they show up there quite a bit. Or any old camera store that has a junk drawer.

_________________
"In order to invent, you need a good imagination and a lot of junk" Thomas Edison
Back to top
View user's profile Send private message
sobahguy



Joined: 09 Oct 2001
Posts: 173
Location: Massachusetts

PostPosted: Thu Aug 08, 2002 4:22 pm    Post subject: Reply with quote

hi,
i needed the same thing a couple of months ago...a 38mm 1-1/2inch slip-on to series VI as Les describes....i made an inquiry here (i think its in the accessories section) then i went to work locating it.
anyway, i found the adapter,retaining ring and even a few filters in just one call to Midwest Photo Exchange in Columbus,OH. check out this site for the phone# and give a call:
http://www.mpex.com
they may also still have quite a few of similar smaller Graphic gadgets that aren't on their site or listed in their Shutterbug ads.
failing that, check out the "where to get" links on this site for other potential suppliers...Pacific Rim Camera comes to mind as well:
http://www.pacificrimcamera.com

Good luck,
SG

[ This Message was edited by: sobahguy on 2002-08-08 09:38 ]
Back to top
View user's profile Send private message
rwarhover



Joined: 11 Aug 2002
Posts: 8
Location: New York City

PostPosted: Sun Aug 11, 2002 11:32 am    Post subject: Reply with quote

For a useful discussionn of push-on "series" sized filters, see:
http://people.smu.edu/rmonagha/bronfilters.html#series
good luck,
Bob Warhover
Back to top
View user's profile Send private message Send e-mail
Mike Wilson



Joined: 02 Aug 2002
Posts: 3

PostPosted: Mon Sep 16, 2002 6:46 pm    Post subject: Reply with quote

To follow up on my earlier question, a 40.5 filter did indeed fit my lens....
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Graflex.org Forum Index -> Lenses Help All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group