View previous topic :: View next topic |
Author |
Message |
Clearfield
Joined: 04 Sep 2002 Posts: 3 Location: New York City
|
Posted: Wed Sep 04, 2002 7:44 pm Post subject: |
|
|
Help! In trying to replace the perfectly functioning 135 cam on my rangefinder with a 90, I screwed up, and can't get either cam to seat properly! Any advice greatly appreciated!!! |
|
Back to top |
|
|
45PSS
Joined: 28 Sep 2001 Posts: 4081 Location: Mid Peninsula, Ca.
|
Posted: Wed Sep 04, 2002 8:14 pm Post subject: |
|
|
Open bed to normal shooting position.
Fold infinity stops out of the way and extend front standard to near end of rails.
Turn camera so that top is toward you and you can see between top and bellows.
Position cam so that tapered side is up, short side to right, tall side to left ( hole to top left,bumps toward lens standard).
Hold open cam cover door, locate slot in cam tube.
Lift follower arm up, locate gap between spring and spacers, push spacers left with edge of cam if necessary .
Now that there is sufficent gap for the cam, insert right edge first (short end) and push to right then seat rest of cam into slot.
Allow follower arm to rest on top of cam.
Extend and return rails the normal focus distance only, to verify proper tracking.
NOTE: Cams will "pop out" of position if the rails are extended beyond the clostest focusing distance of the cam requiring it to be reinstalled before the rails will retract fully.
Charles
_________________
While a picture may be worth a thousand words, a quality photograph is worth a million.
[ This Message was edited by: 45PSS on 2002-09-04 13:17 ]
[ This Message was edited by: 45PSS on 2002-09-04 18:53 ] |
|
Back to top |
|
|
bertsaunders
Joined: 20 May 2001 Posts: 577 Location: Bakersfield California
|
Posted: Thu Sep 05, 2002 2:36 am Post subject: |
|
|
And if that doesnt work....I have the brochure instructions (with photos) of the installation proceedure! Bert |
|
Back to top |
|
|
Clearfield
Joined: 04 Sep 2002 Posts: 3 Location: New York City
|
Posted: Thu Sep 05, 2002 4:17 am Post subject: |
|
|
The problem is--the rangefinder follower arm, and the parallax adjustment arm along with it, keep getting in the way of the cam; if I insert it with my right hand, the cam ends up jamming the follower arm, (yes, I'm trying to hold it back with my left hand, but it doesn't move very far.) If I try to insert the cam with my left hand, I never even get it seated properly. In any case, I can't see through my fingers, which are actually fairly slender, as a man's hand goes. And this was supposed to be user-interchangeable???? What fiend designed this thing??????? |
|
Back to top |
|
|
45PSS
Joined: 28 Sep 2001 Posts: 4081 Location: Mid Peninsula, Ca.
|
Posted: Thu Sep 05, 2002 11:29 am Post subject: |
|
|
One thing I forgot, run the rails out until the follower plunger is or would be fully out. This will widen the slot. Once in return the rails to just touching the plunger as the spring will push the cam out from under its follower arm if the rails are out too far.
They're easy once you get the hang of it, just pratice.
_________________ The best camera ever made is the one that YOU enjoy using and produces the image quality that satifies YOU. |
|
Back to top |
|
|
bertsaunders
Joined: 20 May 2001 Posts: 577 Location: Bakersfield California
|
Posted: Thu Sep 05, 2002 11:34 pm Post subject: |
|
|
Best solution--the original instructions
email me at
bsaunders1@bak.rr.com
Bert
|
|
Back to top |
|
|
Clearfield
Joined: 04 Sep 2002 Posts: 3 Location: New York City
|
Posted: Fri Sep 06, 2002 11:29 pm Post subject: |
|
|
Bert,
That did it!~ Thanks a million!!! The key problem I was having was that the open slot was under the cam follower, and therefore I couldn't get to it. The fix, as the materials you sent me, told me is to extend the focusing rails an inch beyond the camera, and to tap it gently on the handle side to make sure that there is an open stretch of slot into which to insert the cam. Then, it's a piece of cake! Thank you all who sent in advice, and especially you, Bert. Good picture-taking, all! |
|
Back to top |
|
|
bertsaunders
Joined: 20 May 2001 Posts: 577 Location: Bakersfield California
|
Posted: Sat Sep 07, 2002 4:01 am Post subject: |
|
|
Someone keeps saying...a picture is worth a thousand words...and this was the proof. Glad the brochure worked for you! Bert |
|
Back to top |
|
|
|